Alpha 1000 Guía de usuario Pagina 106
- Pagina / 200
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5.6 EISA Configuration Utility
Whenever you add or move EISA options or some ISA options in the system, you
will need to run a utility called the EISA Configuration Utility (ECU). Each EISA
or ISA board has a corresponding configuration (CFG) file, which describes the
characteristics and the system resources required for that option. The ECU uses
the CFG file to create a conflict-free configuration. The ECU is a menu-based
utility that provides online help to guide you through the configuration process.
The ECU is run from the ARC menu interface.
The ECU is supplied on the two System Configuration Diskettes shipped with
the system. Make a backup copy of the system configuration diskette and keep
the original in a safe place. Use the backup copy when you are configuring
the system. The system configuration diskette must have the volume label
‘‘SYSTEMCFG.’’
Note
The CFG files supplied with the option you want to install may not work
on this system if the option is not supported. Before you install an option,
check that the system supports the option.
The version of the ECU that ships with AlphaServer 1000A systems
accommodates 8 EISA slots. However, AlphaServer 1000A systems have
only two EISA slots, slots 1 and 2.
5.6.1 Before You Run the ECU
Before running the ECU:
1. Install EISA option(s). (Install ISA boards after you run the ECU.)
For information about installing a specific option, refer to the documentation
for that option.
2. Familiarize yourself with the utility.
You can find more information about the ECU by reading the ECU online
help. To read the online help, start the ECU (refer to Section 5.6.2). Online
help for the ECU is located under Step 1, ‘‘Important EISA Configuration
Information.’’
3. Familiarize yourself with the configuration procedure for the system:
• If you are configuring an EISA bus that contains only EISA options, refer
to Table 5–6.
5–28 System Configuration and Setup
- AlphaServer 1000A 1
- Service Guide 1
- Contents 3
- 3 Running System Diagnostics 4
- 4 Error Log Analysis 4
- A Default Jumper Settings 6
- Examples 6
- Intended Audience 11
- Conventions 12
- Related Documentation 12
- Troubleshooting Strategy 15
- 1.1.1 Problem Categories 16
- 1–8 Troubleshooting Strategy 22
- 1.3 Information Services 23
- 1–10 Troubleshooting Strategy 24
- Troubleshooting Strategy 1–11 25
- ....done 31
- 12345.done 31
- FAIL B:0 S:2 31
- 2.3 Power-Up Screen 35
- 2.3.1 Console Event Log 37
- 2.5 Storage Device LEDs 41
- Activity LED 42
- 2.8 Fail-Safe Loader 47
- 2.9 Power-Up Sequence 50
- 2.9.2 DC Power-Up Sequence 51
- 2.10.1 Serial ROM Diagnostics 51
- Running System Diagnostics 55
- 3.2 Command Summary 56
- 3.3 Command Reference 57
- 3.3.1 test 58
- 3.3.2 cat el and more el 61
- 3.3.3 memory 62
- 3.3.4 netew 64
- Testing an Ethernet Port: 65
- 3.3.5 network 66
- 3.3.6 net -s 68
- 3.3.7 net -ic 69
- 3.3.8 kill and kill_diags 70
- 3.3.9 show_status 71
- 3.5 DEC VET 72
- Error Log Analysis 73
- Error Log Analysis 4–3 75
- 4–4 Error Log Analysis 76
- 4.3 Event Record Translation 77
- 4–6 Error Log Analysis 78
- System Configuration and Setup 79
- 5.1.1 System Firmware 80
- >>> 81
- >>> set os_type NT 82
- >>> init 82
- Digital UNIX and OpenVMS 87
- Synopsis: 89
- Example: 89
- Key to variable attributes: 94
- Whenever you use the 100
- 5.2 System Bus Options 101
- 5.2.1 CPU Daughter Board 102
- 5.2.2 Memory Modules 102
- 5.3 Motherboard 103
- 5.4 EISA Bus Options 104
- 5.5 ISA Bus Options 105
- 5.6 EISA Configuration Utility 106
- 5.6.2 How to Start the ECU 107
- 5.6.3 Configuring EISA Options 109
- 5.6.4 Configuring ISA Options 110
- 5.7 PCI Bus Options 111
- 5.8 SCSI Buses 112
- 5.8.2 External SCSI Expansion 113
- 5.8.3 SCSI Bus Configurations 114
- 17-03969-01 120
- 5.10.1 set console 121
- 5.10.2 set tt_allow_login 122
- 5.10.3 set tga_sync_green 123
- Replacement 125
- Figure 6–1 FRUs, Front Right 129
- Figure 6–2 FRUs, Rear Left 130
- 6.2 Removal and Replacement 131
- Top Cover 132
- Release Latch 132
- 6.2.1 Cables 133
- Figure 6–7 Power Cord 134
- DC Cable 137
- Assembly 137
- 70-31346-01 138
- External 140
- Terminator 140
- StorageWorks 140
- Backplane 140
- 6.2.3 CPU Daughter Board 145
- 6.2.4 Fans 146
- 6.2.5 StorageWorks Drive 147
- Rear Screws 148
- 6/32 Inch (4) 148
- Internal Screws 148
- 3.5 mm (2) 148
- 6.2.7 Memory Modules 150
- 6.2.8 Interlock Switch 154
- 6.2.9 Motherboard 155
- ECC Banks 159
- 6.2.11 OCP Module 160
- 6.2.12 Power Supply 163
- 6.2.13 Speaker 164
- 6.2.14 Removable Media 165
- Default Jumper Settings 169
- A–2 Default Jumper Settings 170
- A–4 Default Jumper Settings 172
- Default Jumper Settings A–5 173
- Glossary 175
- Glossary–2 176
- Glossary–3 177
- Glossary–4 178
- Glossary–5 179
- Glossary–6 180
- Glossary–7 181
- Glossary–8 182
- Glossary–9 183
- Glossary–10 184
- Glossary–11 185
- Glossary–12 186
- Glossary–13 187
- Glossary–14 188
- Glossary–15 189
- Technical Support 197
- Electronic Orders 197
- BUSINESS REPLY MAIL 200
Relacionado con productos y manuales para Fuentes De Alimentación Alpha 1000
(2 paginas)
(8 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 2.658 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales